Please use this identifier to cite or link to this item: https://bura.brunel.ac.uk/handle/2438/34184
Full metadata record
DC FieldValueLanguage
dc.contributor.authorKhandelwal, Priyansh-
dc.contributor.authorNegrea, Raluca Florentina-
dc.contributor.authorHayat, Asad-
dc.contributor.authorNunn, Jason-
dc.contributor.authorHonan, Scott-
dc.contributor.authorJi, Shouxun-
dc.date.accessioned2026-11-16T18:10:18Z-
dc.date.available2026-11-16T18:10:18Z-
dc.date.issued2026-11-14-
dc.identifier.citationKhandelwal, P. et al. (2026) 'Influence of scandium addition on the castability, elevated-temperature tensile and fatigue performance of A356 alloy', Journal of Alloys and Compounds, 0(in press, pre-proof), 192467, pp. 1–52. doi: 10.1016/j.jallcom.2026.192467.en_GB
dc.identifier.issn0925-8388-
dc.identifier.urihttps://bura.brunel.ac.uk/handle/2438/34184-
dc.descriptionData Availability Statement: Data will be made available on request.en_GB
dc.descriptionThis is a PDF of an article that has undergone enhancements after acceptance, such as the addition of a cover page and metadata, and formatting for readability. This version will undergo additional copyediting, typesetting and review before it is published in its final form. As such, this version is no longer the Accepted Manuscript, but it is not yet the definitive Version of Record; we are providing this early version to give early visibility of the article. Please note that Elsevier’s sharing policy for the Published Journal Article applies to this version, see: https://www.elsevier.com/about/policies-and-standards/sharing#4-publishedjournal-article. Please also note that, during the production process, errors may be discovered which could affect the content, and all legal disclaimers that apply to the journal pertain.en_GB
dc.descriptionSupplementary material is available online at: https://www.sciencedirect.com/science/article/pii/S0925838826065370#sec0130 .en_GB
dc.description.abstractThe influence of scandium (Sc) addition on the fluidity, grain-refinement fading, elevated-temperature tensile performance and fatigue behaviour of A356.2 alloy was systematically investigated. The addition of 0.2 wt.% Sc increased fluidity by 19.5% compared with the baseline alloy, whereas higher Sc additions reduced fluidity because of coarse primary Sc-containing intermetallics. Sc addition significantly refined the grain structure, reduced the secondary dendrite arm spacing (SDAS), modified the eutectic Si morphology and transformed Fe-containing intermetallic phases, resulting in a less heterogeneous microstructure. The Sc-modified alloy also exhibited relatively stable grain size during prolonged melt holding under the present experimental conditions, with only a 14% increase in grain size after 240 min of melt holding. Following T6 heat treatment, the Sc-modified alloy exhibited higher tensile strength and ductility at 200 °C. Atomic-resolution HAADF-STEM and STEM-EDS analyses confirmed ordered AlSc₂Si₂ dispersoids and revealed their close spatial association with Mg-Si-based precipitates and localised Mg enrichment at the dispersoid/α-Al interface. Crystallographic analysis further identified U1-(Al,Si)₂Mg at the examined interface, suggesting that this interfacial configuration may modify the local Mg-Si precipitation environment and contribute to strength retention during elevated-temperature deformation. The A356-0.2Sc-T6 alloy exhibited higher fatigue lives at several investigated stress amplitudes, although the response was not consistently improved across the entire stress range. The results demonstrate that Sc addition can modify the castability, microstructure and mechanical response of A356 alloy under the investigated conditions.en_GB
dc.description.sponsorshipEngineering and Physical Sciences Research Council (EPSRC) under project UKRI1682 and Innovate UK (IUK) under grant number APC 10113213en_GB
dc.format.extentpp. 1–52-
dc.format.mediumPrint-Electronic-
dc.languageEnglish-
dc.language.isoenen_GB
dc.publisherElsevieren_GB
dc.rightsRe-use licence for this version: Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International-
dc.rightsLicence for published version: Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International-
dc.rights.urihttps://creativecommons.org/licenses/by/4.0/-
dc.subjectA356 alloyen_GB
dc.subjectfluidityen_GB
dc.subjectfadingen_GB
dc.subjectfatigue behaviouren_GB
dc.subjectscandiumen_GB
dc.subjecthigh-temperature tensile testen_GB
dc.subject.classification0204 Condensed Matter Physics-
dc.subject.classification0912 Materials Engineering-
dc.subject.classification0914 Resources Engineering and Extractive Metallurgy-
dc.subject.otherMaterials-
dc.titleInfluence of scandium addition on the castability, elevated-temperature tensile and fatigue performance of A356 alloyen_GB
dc.typeArticleen_GB
dc.date.dateAccepted2026-11-13-
dc.identifier.doihttps://doi.org/10.1016/j.jallcom.2026.192467-
dc.relation.isPartOfJournal of Alloys and Compounds-
pubs.publication-statusPublished online-
pubs.volume00-
dc.identifier.eissn1873-4669-
dc.rights.licensehttps://creativecommons.org/licenses/by/4.0/legalcode.en-
dcterms.dateAccepted2026-11-13-
dcterms.issued2026-11-14-
dc.date.updated2026-11-16T12:26:31Z-
dc.rights.holderThe Author(s)-
dc.contributor.orcidKhandelwal, Priyansh [0009-0000-2282-5730]-
dc.contributor.orcidNegrea, Raluca Florentina [0000-0003-2857-0913]-
dc.contributor.orcidJi, Shouxun [0000-0002-8103-8638]-
dc.identifier.number192467-
Appears in Collections:Brunel Centre for Advanced Solidification Technology (BCAST)

Files in This Item:
File Description SizeFormat 
Pre-proof.pdfCopyright © 2026 The Author(s). Published by Elsevier B.V. This is an open access article under a Creative Commons Attribution 4.0 International License (https://creativecommons.org/licenses/by/4.0/).4.21 MBAdobe PDFView/Open


This item is licensed under a Creative Commons License Creative Commons